Select a different country or region to see content for your location.
United States
11:00:27 GMT+0000 (Coordinated Universal Time)







Main Dimensions & Performance Data
H | 48 mm | Total Height |
B1 | 100 mm | Total Width |
L | 100 mm | Length of carriage |
Mounting dimensions
D7 | 16 mm | Tolerance h7 |
D8 | 5,5 mm | |
H1 | 35,5 mm | Height of carriage |
H12 | 11,5 mm | |
JB43 | 88 mm | |
jB8 | 33 mm | |
jL8 | 100 mm | |
K43 | M5 | |
Ltot | 2.900 mm | Maximum length |
Rx | 55,6 mm | |
S | 3 mm | Safety distance |
S | 10 mm | |
T8 | 5,6 mm | |
T86 | 3 mm | Depth Fit |
t43 | 13 mm | Depth of Thread |
t87 | 12 mm | Depth of Thread |
BB | 21 mm | Length of Bellows Fastener |
FBL | 1,58 mm | Effective length factor of bellow |
b87 | 44 mm | Tolerance ±0,2 |
d85 | 5 mm | Diameter drive shaft, Tolerance h7 1 |
D86 | 17 mm | Tolerance H7 |
G4 | M8 | Thread |
G5 | M8 | Thread |
G87 | M5 | Thread |
G43 | M6 | Thread |
h5 | 16 mm | |
h85 | 26 mm | |
h87 | 22 mm | Tolerance ±0,2 |
JL43 | 88 mm | |
jB43 | 88 mm | |
jB4 | 82 mm | |
JL4 | 9 mm |
Dimensions
H7 | 5 mm | |
h1 | 22 mm | |
L4 | 24 mm | Length of Shaft Support Block with Drive System |
L5 | 18 mm | Length of Shaft Support Block without drive System |
L88 | 28,5 mm | |
Rz | 54 mm | |
H5 | 32 mm | Height of Shaft Support Blocks |
Technical data
vmax | 0,075 m/s | Maximum Speed |
amax | 2,5 m/s2 | Maximum Acceleration |
d0 | 12 mm | Spindle Diameter |
P | 3 mm | Spindle Pitch |
mLAW | 0,8 kg | Mass of Carriage |
Is | 0,094 kg*cm2 | Mass moment of inertia of threaded Spindle |
CI | 2.110 N | Load direction I: compressive load |
C0I | 2.480 N | Load direction I: compressive load |
CII | 880 N | Load direction II: tensile load |
C0II | 1.140 N | Load direction II: tensile load |
CIII | 2.240 N | Load direction III: lateral load |
C0III | 2.900 N | Load direction III: lateral load 2 |
C0 | 630 N | Load capacity Spindle Nut stat 3 |
C0a | 630 N | Load capacity fixed Spindle bearing stat |
M0x | 29 Nm | Max. permissible static moment per Carriage 3 |
M0y | 50 Nm | Max. permissible static moment per Carriage 3 |
M0z | 32 Nm | Max. permissible static moment per Carriage 3 |
Additional information
1,5 Nm | Max. permissible drive torque | |
30/6-2RS | Rolling Bearings | |
0,094 kg*cm2 | Mass moment of inertia of threaded Spindle | |
KBO16-PP-AS | Bearing 2 |
Temperature range
min | 0 °C | Minimum operating Temperatur |
max | 80 °C | Maximum operating Temperatur |
Footnotes
1
Thread witness marks may be present on the pin.
2
Design of linear ball bearing guidance systems: see Catalogue WF1, Shaft Guidance Systems.
3
These values apply if load is evenly distributed over all four linear ball bearings. The values are single loads and apply when the shaft and support rail units are fully supported. These must be reduced for combined loads. For design criteria of the linear guidance system, see Catalogue WF1, Shaft Guidance Systems.
Downloads:
Your current product variant
Size code | 16 | |
Drive type | TGT | Trapezoidal screw drive |
Length of carriage | 100 | 100 mm |
Spindle diameter | 12 | 12mm |
Spindle pitch | 03 | 3 mm |
Spindle nut design | M | Cylinder nut |
Bellow | 1 | Yes |

