Sélectionnez un autre pays ou une autre région pour voir le contenu correspondant à votre emplacement.
Etats Unis
07:12:37 GMT+0000 (Coordinated Universal Time)


MKLF52-500-EE-ZR
Module de guidage linéaire
Actionneurs de serrage avec système de guidage à galet de came externe et entraînement à courroie crantée. Conception de base, deux chariots entraînés dans des directions opposées
Information produit









Cotes métriques
Cotes impériales
dimensions principale & données de performance
B1 | 155 mm | Total Width |
H | 125 mm | Height |
L | 500 mm | Length |
Cotes de montage
D86 | 95 mm | |
D87 | 115 mm | Ø Bolt circle |
d85 | 20 mm | |
d86 | 76 mm | Ø Inner Fit |
L88 | 31 mm | |
G43 | M12 | Thread |
G87 | M8 | Thread |
h85 | 60,6 mm | |
JB43 | 115 mm | |
JL43 | 180 mm | Tolerance ±0,2 |
JL44 | 420 mm | |
jB8 | 80 mm | |
NB85 | 6 mm | Width of Keyway |
NL85 | 25 mm | Length of Keyway |
NT85 | 3,5 mm | Depth of Keyway |
T86 | 4 mm | Depth Fit |
Tol T86 up | 0,5 mm | Upper tolerance |
Tol T86 low | 0 mm | Lower tolerance |
t43 max | 24 mm | Depth of Thread |
t87 max | 15 mm |
Dimensions
B2 | 112 mm | Width of Support Rail |
B4 | 111 mm | Width of Return Unit |
B72 | 2 mm | |
H1 | 70 mm | |
H2 | 98,6 mm | Height |
H4 | 118,3 mm | Height of Return Unit |
H7 | 65,4 mm | |
h13 | 25 mm | |
h14 | 50 mm | |
L2 max | 8.000 mm | Maximum length of Support Rail |
L4 | 115,5 mm | |
L6 | 6 mm | Length of Wiper Brushes |
S | 85 mm | Dimension |
Données techniques
mLAW | 15,86 kg | Mass of Carriage |
vmax | 8 m/s | Maximum Speed |
amax | 40 m/s2 | Maximum Acceleration |
Rx | 360 mm | |
Ry | 95 mm | |
Rz | 386 mm | |
I C | 20.000 N | Load direction I: compressive load |
I C0 | 10.000 N | Load direction I: compressive load |
II C | 20.000 N | Load direction II: tensile load |
II C0 | 10.000 N | Load direction II: tensile load |
III C | 32.400 N | Load direction III: lateral load |
III C0 | 18.200 N | Load direction III: lateral load |
M0x per | 215 Nm | Max. permissible static moment per Carriage 1 |
M0y per | 3.300 Nm | Max. permissible static moment per Carriage 1 |
M0z per | 1.800 Nm | Max. permissible static moment per Carriage 1 |
Iy | 386 cm4 | Geometrical moments of inertia of Support Rail 2 |
Iz | 301 cm4 | Geometrical moments of inertia of Support Rail 2 |
information additionnelle
1.780 Nm | Max. permissible drive torque | |
4xLFR5302-10-2Z | Track Rollers | |
0,1 mm | Repeat Accurancy ± | |
270 mm | Feed (mm/rotation) | |
32AT10 | Toothed Belt | |
0,2 kg/m | Mass of Toothed Belt | |
1.750 N | Permissible Toothed Belt operating force | |
12,6 kg*cm2 | Mass moment of inertia of Gears |
Plage de température
Tmin | 0 °C | Minimum operating Temperatur |
Tmax | 80 °C | Maximum operating Temperatur |
Notes de bas de page
1
The values are single loads and apply when the underside of the actuator is fully supported. If there are several carriage units per actuator or combined loads are present, these must be reduced.
2
Moment of inertia of area of “closed” support rail (= support rail without free milled area on base). In comparison with these values, the moment of inertia of area Iy of the side with the free milled area on the base is reduced to an insignificant degree and the moment of inertia of area Iz is reduced by approx. 10%.
Téléchargements :
Votre alternative produit actuelle
Size code | 52 | |
Length of carriage | 500 | 500 mm |
Carriage design | EE | Double strengthened carriage |
Drive type | (3)ZR | Toothed belt drive |
Additional carriage | / | No additional carriage |
Support rail design | / | One-piece |
Bellow | / | No |
Produits récemment consultés